becton dickinson and company - Medication Listings

3% Sodium Chloride Injection, USP is a sterile, nonpyrogenic, hypertonic solution for fluid and electrolyte replenishment in single dose containers for intravenous administration. The pH may have been adjusted with hydrochloric acid. It contains no antimicrobial agents. Composition, ionic concentration, osmolarity, and pH are shown in Table 1 . Table 1. *Normal physiological osmolarity range is approximately 280 to 310 mOsmol/L. Size (mL) Composition (g/L) Ionic Concentration (mEq/L) *Osmolarity (mOsmol/L) (calc) pH Sodium Chloride, USP (NaCl) Sodium Chloride 3% Sodium Chloride Injection, USP 500 30 513 513 1,027 5.0 (4.5 to 7.0) The flexible container is fabricated from a specially formulated non-plasticized, film containing polypropylene and thermoplastic elastomers (free flex ® bag). The amount of water that can permeate from the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the flexible container can leach out certain of the container's chemical components in very small amounts within the expiration period. The suitability of the container material has been confirmed by tests in animals according to USP biological tests for plastic containers.

Use preoperative cleaning of healthcare personnel arms and hands. Significantly reduces the number of micro-organisms on the hands and forearms prior to surgery.

Use preoperative cleaning of healthcare personnel arms and hands. Significantly reduces the number of micro-organisms on the hands and forearms prior to surgery.

Use preoperative cleaning of healthcare personnel arms and hands.

5% Dextrose Injection, USP solution is sterile and nonpyrogenic. It is a parenteral solution containing dextrose in water for injection intended for intravenous administration. Each 100 mL of 5% Dextrose Injection, USP, contains dextrose monohydrate, 5 g in water for injection. The caloric value is 170 kcal/L. The osmolarity is 252 mOsmol/L (calc.), which is slightly hypotonic. The solution pH is 4.3 (3.2 to 6.5). This solution contains no bacteriostat, antimicrobial agent or added buffer and is intended only as a single-dose injection. When smaller doses are required the unused portion should be discarded. 5% Dextrose Injection, USP is a parenteral fluid and nutrient replenisher. Dextrose, USP is chemically designated D-glucose monohydrate (C 6 H 12 O 6 • H 2 O), a hexose sugar freely soluble in water. It has the following structural formula: Water for Injection, USP is chemically designated H 2 O. The flexible container is fabricated from a specially formulated non-plasticized film containing polypropylene and thermoplastic elastomers ( free flex ® bag). The free flex ® + bag has a needle-free injection port and can accept standard luer lock syringes to add medication. The amount of water that can permeate from the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the flexible container can leach out certain of the container's chemical components in very small amounts within the expiration period. The suitability of the container material has been confirmed by tests in animals according to USP biological tests for plastic containers. Structural Formula

5% Dextrose Injection, USP solution is sterile and nonpyrogenic. It is a parenteral solution containing dextrose in water for injection intended for intravenous administration. Each 100 mL of 5% Dextrose Injection, USP, contains dextrose monohydrate, 5 g in water for injection. The caloric value is 170 kcal/L. The osmolarity is 252 mOsmol/L (calc.), which is slightly hypotonic. The solution pH is 4.3 (3.2 to 6.5). This solution contains no bacteriostat, antimicrobial agent or added buffer and is intended only as a single-dose injection. When smaller doses are required the unused portion should be discarded. 5% Dextrose Injection, USP is a parenteral fluid and nutrient replenisher. Dextrose, USP is chemically designated D-glucose monohydrate (C 6 H 12 O 6 • H 2 O), a hexose sugar freely soluble in water. It has the following structural formula: Water for Injection, USP is chemically designated H 2 O. The flexible container is fabricated from a specially formulated non-plasticized film containing polypropylene and thermoplastic elastomers ( free flex ® bag). The amount of water that can permeate from the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the flexible container can leach out certain of the container's chemical components in very small amounts within the expiration period. The suitability of the container material has been confirmed by tests in animals according to USP biological tests for plastic containers. Structural Formula

10% Dextrose Injection, USP is a sterile, non-pyrogenic solution for fluid replenishment and caloric supply in single dose containers for intravenous administration. The solution contains no bacteriostatic, antimicrobial agent or added buffer and is intended only for use as a single-dose injection. The pH range is 4.0 (3.2 to 6.5) Table 1. Contents and Characteristics of Dextrose Injection 10%, USP *Caloric value calculated on the basis of 3.4 kcal/g of dextrose, hydrous Strength Fill Volume Amount of Dextrose Hydrous per Container kcal* per Container Osmolarity (mOsmol per liter) Dextrose Injection 10%, USP (0.1 grams/mL) 250 mL 25 grams 85 505 500 mL 50 grams 170 505 1000 mL 100 grams 340 505 Dextrose, USP is chemically designated D-glucose, monohydrate (C 6 H 12 O 6 • H 2 O), a hexose sugar freely soluble in water. The molecular weight of dextrose (D-glucose) monohydrate is 198.17. It has the following structural formula: Water for Injection, USP is chemically designated H 2 O. Dextrose is derived from corn. The flexible container is fabricated from a specially formulated non-plasticized, film containing polypropylene and thermoplastic elastomers ( free flex ® bag). The amount of water that can permeate from the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the flexible container can leach out certain of the container's chemical components in very small amounts within the expiration period. The suitability of the container material has been confirmed by tests in animals according to USP biological tests for plastic containers. The flexible container is a closed system, and air is prefilled in the container to facilitate drainage. The container does not require entry of external air during administration. The container has two ports: one is the administration outlet port for attachment of an intravenous administration set and the other port has a medication site for addition of supplemental medication ([see Instructions for Use ( 2.3 )]). The primary function of the overwrap is to protect the container from the physical environment. Structural Formula

Dextrose and Sodium Chloride Injection, USP solutions are sterile and nonpyrogenic. They are large volume parenteral solutions containing 5 grams per 100 mL of Dextrose monohydrate and 0.9 grams per 100 mL of Sodium Chloride in water for injection intended for intravenous administration. Electrolytes per 1000 mL: sodium (Na + ), 154 mEq; chloride (Cl - ) 154 mEq. The osmolarity is 560 mOsmol/L (calc.), which is hypertonic. The caloric value is 170 kcal/L. The pH is 4.3 (3.5 to 6.5). The solutions contain no bacteriostat, antimicrobial agent or added buffer and each is intended only as a single-dose injection. When smaller doses are required the unused portion should be discarded. The solutions are parenteral fluid, nutrient and electrolyte replenishers. Dextrose, USP is chemically designated D-glucose monohydrate (C 6 H 12 O 6 • H 2 O), a hexose sugar freely soluble in water. It has the following structural formula: Sodium Chloride, USP is chemically designated NaCl, a white crystalline powder freely soluble in water. Water for Injection, USP is chemically designated H 2 O. The flexible container is fabricated from a specially formulated non-plasticized, film containing polypropylene and thermoplastic elastomers ( free flex ® bag). The amount of water that can permeate from the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the flexible container can leach out certain of the container's chemical components in very small amounts within the expiration period. The suitability of the container material has been confirmed by tests in animals according to USP biological tests for plastic containers. Structural Formula

5% Dextrose and 0.45% Sodium Chloride Injection, USP solutions are sterile and nonpyrogenic. They are large volume parenteral solutions containing 5 grams per 100 mL of Dextrose monohydrate and 0.45 grams per 100 mL of Sodium Chloride in water for injection intended for intravenous administration. Each 100 mL of 5% Dextrose and 0.45% Sodium Chloride Injection, USP contains dextrose, hydrous 5 g and sodium chloride 0.45 g in water for injection. Electrolytes per 1000 mL: sodium (Na + ), 77 mEq; chloride (Cl - ) 77 mEq. The osmolarity is 406 mOsmol/L (calc.), which is hypertonic. The caloric value is 170 kcal/L. The pH is 4.3 (3.5 to 6.5). 5% Dextrose and 0.45% Sodium Chloride Injection, USP contains no bacteriostat, antimicrobial agent or added buffer and is intended only as a single-dose injection. When smaller doses are required the unused portion should be discarded. 5% Dextrose and 0.45% Sodium Chloride Injection, USP is a parenteral fluid, nutrient and electrolyte replenisher. Dextrose, USP is chemically designated D-glucose monohydrate (C 6 H 12 O 6 • H 2 O), a hexose sugar freely soluble in water. It has the following structural formula: Sodium Chloride, USP is chemically designated NaCl, a white crystalline powder freely soluble in water. Water for Injection, USP is chemically designated H 2 O. The flexible container is fabricated from a specially formulated non-plasticized, film containing polypropylene and thermoplastic elastomers ( free flex ® bag). The amount of water that can permeate from the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the flexible container can leach out certain of the container's chemical components in very small amounts within the expiration period. The suitability of the container material has been confirmed by tests in animals according to USP biological tests for plastic containers. Structural Formula

Use for the preparation of skin prior to an injection to decrease germs in minor cuts and scrapes.

Lactated Ringer's Injection, USP is a sterile, nonpyrogenic solution for fluid and electrolyte replenishment in single dose containers for intravenous administration. It contains no antimicrobial agents. Composition, osmolarity, pH, ionic concentration and caloric content are shown in Table 1 . Table 1 Size (mL) Composition (g/L) Ionic Composition (mEq/L) Caloric Content (kcal/L) Sodium Chloride, USP (NaCl) Sodium Lactate, USP (C 3 H 5 NaO 3 ) Potassium Chloride, USP (KCl) Calcium Chloride, USP (CaCl 2 •2H 2 O) Osmolarity (mOsmol/L) (calc) pH Sodium Potassium Calcium Chloride Lactate Lactated Ringer's Injection, USP 250 6 3.1 0.3 0.2 273 6.5 (6.0 to 7.5) 130 4 2.7 109 28 9 500 1,000 The flexible container is fabricated from a specially formulated non-plasticized, film containing polypropylene and thermoplastic elastomers ( free flex ® bag). The amount of water that can permeate from inside the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the flexible container can leach out certain of the container's chemical components in very small amounts within the expiration period. The suitability of the container material has been confirmed by tests in animals according to USP biological tests for plastic containers.

Each 100 mL contains: Sodium Chloride, USP 0.9 g; Water for Injection, USP qs pH adjusted with Hydrochloric Acid, NF pH: 5.75 (4.50-7.00) Calculated Osmolarity: 308 mOsmol/liter Concentration of Electrolytes (mEq/liter): Sodium 154; Chloride 154 0.9% Sodium Chloride Irrigation, USP is sterile, nonpyrogenic, isotonic and contains no bacteriostatic or antimicrobial agents. The formula of the active ingredient is: Ingredient Molecular Formula Molecular Weight Sodium Chloride, USP NaCl 58.44 The flexible plastic container is made from a multilayered film specifically developed for parenteral drugs. It contains no plasticizers. The solution contact layer is a copolymer of ethylene and propylene. The container is nontoxic and biologically inert. The container-solution unit is a closed system and is not dependent upon entry of external air during administration. Not made with natural rubber latex, PVC or DEHP.

0.9% Sodium Chloride Injection, USP solution is sterile and nonpyrogenic. It is a parenteral solution containing sodium chloride in water for injection intended for intravenous administration. For 0.9% Sodium Chloride Injection, USP, each 100 mL contains 900 mg sodium chloride in water for injection. Electrolytes per 1,000 mL: sodium 154 mEq; chloride 154 mEq. The osmolarity is 308 mOsmol/L (calc.). The pH in the 100 mL and smaller containers is 6.0; for the 250 mL and larger containers, the pH is 5.6. The pH range is 4.5 to 7.0 for all containers. The solution contains no bacteriostat, antimicrobial agent or added buffer and is intended only as a single-dose injection. When smaller doses are required the unused portion should be discarded. The solution is a parenteral fluid and electrolyte replenisher. Sodium Chloride, USP is chemically designated NaCl, a white crystalline powder freely soluble in water. Water for injection, USP is chemically designated H 2 O. The flexible container is fabricated from a specially formulated non-plasticized, film containing polypropylene and thermoplastic elastomers ( free flex ® bag). The amount of water that can permeate from the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the flexible container can leach out certain of the container's chemical components in very small amounts within the expiration period. The suitability of the container material has been confirmed by tests in animals according to USP biological tests for plastic containers.

0.9% Sodium Chloride Injection, USP solution is sterile and nonpyrogenic. It is a parenteral solution containing sodium chloride in water for injection intended for intravenous administration. For 0.9% Sodium Chloride Injection, USP, each 100 mL contains 900 mg sodium chloride in water for injection. Electrolytes per 1,000 mL: sodium 154 mEq; chloride 154 mEq. The osmolarity is 308 mOsmol/L (calc.). The pH in the 100 mL and smaller containers is 6.0; for the 250 mL and larger containers, the pH is 5.6. The pH range is 4.5 to 7.0 for all containers. The solution contains no bacteriostat, antimicrobial agent or added buffer and is intended only as a single-dose injection. When smaller doses are required the unused portion should be discarded. The solution is a parenteral fluid and electrolyte replenisher. Sodium Chloride, USP is chemically designated NaCl, a white crystalline powder freely soluble in water. Water for injection, USP is chemically designated H 2 O. The flexible container is fabricated from a specially formulated non-plasticized, film containing polypropylene and thermoplastic elastomers ( free flex ® bag). The free flex ® + bag has a needle-free injection port and can accept standard luer lock syringes to add medication. The amount of water that can permeate from the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the flexible container can leach out certain of the container's chemical components in very small amounts within the expiration period. The suitability of the container material has been confirmed by tests in animals according to USP biological tests for plastic containers.

0.45% Sodium Chloride Injection, USP solution is a sterile and nonpyrogenic solution intended for intravenous administration. Each 100 mL of 0.45% Sodium Chloride Injection, USP contains 450 mg sodium chloride in water for injection. Electrolytes per 1,000 mL: sodium 77 mEq; chloride 77 mEq. The osmolarity is 154 mOsmol/L (calc.). The pH in the 100 mL and smaller containers is 6.0; for the 250 mL and larger containers, the pH is 5.6. The pH range is 4.5 to 7.0 for all containers. The solution contains no bacteriostat, antimicrobial agent or added buffer and is intended only as a single-dose injection. When smaller doses are required the unused portion should be discarded. 0.45% Sodium Chloride Injection, USP is a parenteral fluid and electrolyte replenisher. Sodium chloride, USP is chemically designated NaCl, a white crystalline powder freely soluble in water. Water for Injection, USP is chemically designated H 2 O. The flexible plastic container is fabricated from a specially formulated non-plasticized, film containing polypropylene and thermoplastic elastomers ( free flex ® bag). The amount of water that can permeate from the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the flexible container can leach out certain of the container's chemical components in very small amounts within the expiration period. The suitability of the container material has been confirmed by tests in animals according to USP biological tests for plastic containers.

Sterile Water for Irrigation, USP is a sterile, hypotonic, nonpyrogenic irrigating fluid or pharmaceutic aid (solvent) entirely composed of Sterile Water for Injection, USP. It is prepared by distillation and contains no antimicrobial or bacteriostatic agents or added buffers. The pH is 5.7 (5.0-7.0) The flexible plastic container is made from a multilayered film specifically developed for parenteral drugs. It contains no plasticizers. The solution contact layer is a copolymer of ethylene and propylene. The container is nontoxic and biologically inert. The container-solution unit is a closed system and is not dependent upon entry of external air during administration. Not made with natural rubber latex, PVC or DEHP.

Sterile Water for Injection, USP is a sterile, nonpyrogenic, solute-free preparation of distilled water for injection. It is for use only as a sterile solvent or diluent vehicle for drugs or solutions suitable for parenteral administration. The pH is 5.5 (5.0 to 7.0). Sterile Water for Injection contains no bacteriostat, antimicrobial agent or added buffer and is intended only for single dose injection after admixture with an appropriate solute or solution. When smaller amounts are required, the unused portion should be discarded. Sterile Water for Injection is a pharmaceutic aid (vehicle) and parenteral fluid replenisher after addition of an appropriate solute. Water for Injection, USP is chemically designated H 2 O. The flexible container is fabricated from a specially formulated non-plasticized, film containing polypropylene and thermoplastic elastomers (free flex ® bag). The amount of water that can permeate from the container into the overwrap is insufficient to affect the solution significantly. Solutions in contact with the flexible container can leach out certain of the container's chemical components in very small amounts within the expiration period. The suitability of the container material has been confirmed by tests in animals according to USP biological tests for plastic containers.