enoxaparin sodium - Medication Listings

Enoxaparin Sodium Injection, USP is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4,500 daltons. The molecular weight distribution is: <2,000 daltons ≤20% 2,000 to 8,000 daltons ≥68% >8,000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6-anhydro derivative on the reducing end R X*=15 to 25% n=0 to 20 100-X H n=1 to 21 Enoxaparin Sodium Injection, USP 100 mg per mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin Sodium Injection, USP 150 mg per mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The Enoxaparin Sodium Injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 )] . figure figure

Enoxaparin Sodium Injection, USP is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4,500 daltons. The molecular weight distribution is: <2,000 daltons ≤20% 2,000 to 8,000 daltons ≥68% >8,000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6-anhydro derivative on the reducing end R X*=15 to 25% n=0 to 20 100-X H n=1 to 21 Enoxaparin Sodium Injection, USP 100 mg per mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin Sodium Injection, USP 150 mg per mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The Enoxaparin Sodium Injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 )] . structural formula 1 structural formula 2

Enoxaparin Sodium Injection USP is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6 anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA R X Percent of polysaccharide chain containing 1,6 anhydro derivative on the reducing end = 15 to 25% n=0 to 20 100 - X H n=1 to 21 Enoxaparin Sodium Injection USP 100 mg/mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin Sodium Injection USP 150 mg/mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The Enoxaparin Sodium Injection USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection. The multiple-dose vial contains 15 mg benzyl alcohol per 1 mL as a preservative [ see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling( 16 ) ]. chemical structure chemical structure

Enoxaparin sodium injection is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains an 1,6 anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA R X*= 15 to 25% n= 0 to 20 100 - X H n =1 to 21 * X = Percent of polysaccharide chain containing 1, 6 anhydro derivative on the reducing end. Enoxaparin sodium injection 100 mg/mL concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin sodium injection 150 mg/mL concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection [see Dosage and Administration (2) and How Supplied/Storage and Handling (16) ]. enoxaparin-spl-structure enoxaparin-spl-structure1

Enoxaparin Sodium Injection, USP is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4,500 daltons. The molecular weight distribution is: <2,000 daltons ≤20% 2,000 to 8,000 daltons ≥68% >8,000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6 anhydro derivative on the reducing end R X*=15 to 25% n=0 to 20 100-X H n=1 to 21 Enoxaparin Sodium Injection, USP 100 mg per mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The Enoxaparin Sodium Injection, USP multi-dose vial contains 15 mg benzyl alcohol per 1 mL as a preservative [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 )] . structural formula structural formula

Enoxaparin sodium injection is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains an 1,6 anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6 anhydro derivative on the reducing end. R X*= 15 to 25% n= 0 to 20 100 - X H n =1 to 21 Enoxaparin sodium injection 100 mg per mL concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin sodium injection 150 mg per mL concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 )] . Figure Figure

Enoxaparin Sodium Injection, USP is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4,500 daltons. The molecular weight distribution is: <2,000 daltons ≤20% 2,000 to 8,000 daltons ≥68% >8,000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6 anhydro derivative on the reducing end R X*=15 to 25% n=0 to 20 100-X H n=1 to 21 Enoxaparin Sodium Injection, USP 100 mg per mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The Enoxaparin Sodium Injection, USP multi-dose vial contains 15 mg benzyl alcohol per 1 mL as a preservative [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 )] . structural formula structural formula

Enoxaparin sodium injection is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA R X X = Percent of polysaccharide chain containing 1,6-anhydro derivative on the reducing end =15 to 25% n=0 to 20 100-X H n=1 to 21 Enoxaparin sodium injection 100 mg/mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin sodium injection 150 mg/mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection. The multiple-dose vial contains 15 mg benzyl alcohol per 1 mL as a preservative [see Dosage and Administration (2) and How Supplied/Storage and Handling (16) ] . Chemical Structure Chemical Structure

Enoxaparin sodium injection, USP is a sterile aqueous solution containing enoxaparin sodium, USP a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium, USP is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% Structural Formula * X = Percent of polysaccharide chain containing 1,6-anhydro derivative on the reducing end Enoxaparin sodium injection USP, 100 mg/mL Concentration contains 10 mg enoxaparin sodium, USP (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin sodium injection USP, 150 mg/mL Concentration contains 15 mg enoxaparin sodium, USP (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection. [ see Dosage and Administration (2) and How Supplied/Storage and Handling (16)]. structure

Enoxaparin sodium injection is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains an 1,6 anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6 anhydro derivative on the reducing end. R X * = 15 to 25% n= 0 to 20 100 - X H n =1 to 21 Enoxaparin sodium injection 100 mg/mL concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin sodium injection 150 mg/mL concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection [ see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 ) ]. enoxa-struc-01.jpg enoxa-struc-02.jpg

Enoxaparin sodium injection is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains an 1,6 anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6 anhydro derivative on the reducing end. R X * = 15 to 25% n= 0 to 20 100 - X H n =1 to 21 Enoxaparin sodium injection 100 mg/mL concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin sodium injection 150 mg/mL concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection [ see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 ) ]. enoxa-struc-01.jpg enoxa-struc-02.jpg

Summary not available yet.

Enoxaparin sodium injection, USP is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6 anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA Enoxaparin Sodium Injection, USP 100 mg/mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin Sodium Injection, USP 150 mg/mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection. [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 ) ] . Enoxaparin Sodium Chemical Structure

Enoxaparin sodium injection, USP is a sterile aqueous solution containing enoxaparin sodium USP, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains an 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA *X = Percent of polysaccharide chain containing 1,6-anhydro derivative on the reducing end R X*=15 to 25% n=0 to 20 100-X H n=1 to 21 Enoxaparin sodium injection, USP 100 mg/mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin sodium injection, USP 150 mg/mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection. [see Dosage and Administration (2) and How Supplied/Storage and Handling (16) ] . enoxaparin-str1 enoxaparin-str2

Enoxaparin sodium injection is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains an 1,6 anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6 anhydro derivative on the reducing end. R X*= 15 to 25% n= 0 to 20 100 - X H n = 1 to 21 Enoxaparin sodium injection 100 mg per mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin sodium injection 150 mg per mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 ) ]. structural formula structural formula

Enoxaparin sodium injection is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA R 1 = H or SO 3 Na and R 2 = SO 3 Na or COCH 3 R X X = Percent of polysaccharide chain containing 1,6-anhydro derivative on the reducing end =15 to 25% n=0 to 20 100-X H n=1 to 21 Enoxaparin sodium injection 100 mg/mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin sodium injection 150 mg/mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection. The multiple-dose vial contains 15 mg benzyl alcohol per 1 mL as a preservative [see Dosage and Administration (2) and How Supplied/Storage and Handling (16) ] . Chemical Structure Chemical Structure

Enoxaparin sodium injection, USP is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6 anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA Enoxaparin Sodium Injection, USP 100 mg/mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin Sodium Injection, USP 150 mg/mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection. [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 ) ] . Enoxaparin Sodium Chemical Structure

Enoxaparin sodium injection is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains an 1,6 anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6 anhydro derivative on the reducing end. R X*= 15 to 25% n= 0 to 20 100 - X H n =1 to 21 Enoxaparin sodium injection 100 mg per mL concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium injection, USP prefilled syringes are preservative-free and intended for use only as a single-dose injection [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 )] . Structural Formula Structural Formula

Enoxaparin Sodium Injection, USP is an aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4,500 daltons. The molecular weight distribution is: <2,000 daltons ≤20% 2,000 to 8,000 daltons ≥68% >8,000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6-anhydro derivative on the reducing end R X*=15 to 25% n=0 to 20 100-X H n=1 to 21 Enoxaparin Sodium Injection, USP 100 mg per mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin Sodium Injection, USP 150 mg per mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The Enoxaparin Sodium Injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 )] . Figure Figure

Enoxaparin sodium injection is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA R 1 = H or SO 3 Na and R 2 = SO 3 Na or COCH 3 R X X = Percent of polysaccharide chain containing 1,6-anhydro derivative on the reducing end =15 to 25% n=0 to 20 100-X H n=1 to 21 Enoxaparin sodium injection 100 mg/mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin sodium injection 150 mg/mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection. The multiple-dose vial contains 15 mg benzyl alcohol per 1 mL as a preservative [see Dosage and Administration (2) and How Supplied/Storage and Handling (16) ] . Chemical Structure Chemical Structure

Enoxaparin Sodium Injection, USP is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4,500 daltons. The molecular weight distribution is: <2,000 daltons ≤20% 2,000 to 8,000 daltons ≥68% >8,000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6-anhydro derivative on the reducing end R X*=15 to 25% n=0 to 20 100-X H n=1 to 21 Enoxaparin Sodium Injection, USP 100 mg per mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin Sodium Injection, USP 150 mg per mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The Enoxaparin Sodium Injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 )] . figure figure

Enoxaparin Sodium Injection, USP is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4,500 daltons. The molecular weight distribution is: <2,000 daltons 20% 2,000 to 8,000 daltons 68% >8,000 daltons 18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6-anhydro derivative on the reducing end Enoxaparin Sodium Injection, USP 100 mg per mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin Sodium Injection, USP 150 mg per mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The Enoxaparin Sodium Injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 )] . Structural Formula Structural Formula

Enoxaparin Sodium Injection USP is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6 anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons 20% 2000 to 8000 daltons 68% >8000 daltons 18% STRUCTURAL FORMULA R X X = Percent of polysaccharide chain containing 1,6 anhydro derivative on the reducing end =15 to 25% n=0 to 20 100 - X H n=1 to 21 Chemical Structure Chemical Structure Enoxaparin Sodium Injection USP 100 mg/mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin Sodium Injection USP 150 mg/mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The Enoxaparin Sodium Injection USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection. The multiple-dose vial contains 15 mg benzyl alcohol per 1 mL as a preservative [ see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling( 16 ) ].

Enoxaparin Sodium Injection USP is a sterile aqueous solution containing enoxaparin sodium, USP, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium, USP is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6-anhydro derivative on the reducing end. Enoxaparin Sodium Injection USP, 100 mg/mL Concentration contains 10 mg enoxaparin sodium, USP (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin Sodium Injection USP, 150 mg/mL Concentration contains 15 mg enoxaparin sodium, USP (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The Enoxaparin Sodium Injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 )] . Structural Formula Structural Formula 2

Enoxaparin Sodium Injection, USP is a sterile aqueous solution containing enoxaparin sodium, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains a 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4,500 daltons. The molecular weight distribution is: <2,000 daltons ≤20% 2,000 to 8,000 daltons ≥68% >8,000 daltons ≤18% STRUCTURAL FORMULA * X = Percent of polysaccharide chain containing 1,6 anhydro derivative on the reducing end R X*=15 to 25% n=0 to 20 100-X H n=1 to 21 Enoxaparin Sodium Injection, USP 100 mg per mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1,000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The Enoxaparin Sodium Injection, USP multi-dose vial contains 15 mg benzyl alcohol per 1 mL as a preservative [see Dosage and Administration ( 2 ) and How Supplied/Storage and Handling ( 16 )] . structural formula structural formula

Enoxaparin sodium injection, USP is a sterile aqueous solution containing enoxaparin sodium USP, a low molecular weight heparin. The pH of the injection is 5.5 to 7.5. Enoxaparin sodium is obtained by alkaline depolymerization of heparin benzyl ester derived from porcine intestinal mucosa. Its structure is characterized by a 2-O-sulfo-4-enepyranosuronic acid group at the non-reducing end and a 2-N,6-O-disulfo-D-glucosamine at the reducing end of the chain. About 20% (ranging between 15% and 25%) of the enoxaparin structure contains an 1,6-anhydro derivative on the reducing end of the polysaccharide chain. The drug substance is the sodium salt. The average molecular weight is about 4500 daltons. The molecular weight distribution is: <2000 daltons ≤20% 2000 to 8000 daltons ≥68% >8000 daltons ≤18% STRUCTURAL FORMULA *X = Percent of polysaccharide chain containing 1,6-anhydro derivative on the reducing end R X*=15 to 25% n=0 to 20 100-X H n=1 to 21 Enoxaparin sodium injection, USP 100 mg/mL Concentration contains 10 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1000 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. Enoxaparin sodium injection, USP 150 mg/mL Concentration contains 15 mg enoxaparin sodium (approximate anti-Factor Xa activity of 1500 IU [with reference to the W.H.O. First International Low Molecular Weight Heparin Reference Standard]) per 0.1 mL Water for Injection. The enoxaparin sodium injection, USP prefilled syringes and graduated prefilled syringes are preservative-free and intended for use only as a single-dose injection. [see Dosage and Administration (2) and How Supplied/Storage and Handling (16) ] . enoxaparin-str1 enoxaparin-str2